The radial arm saw uses a design that is unusual for stationary power tools since the entire motor and blade unit mounted on an overhead arm moves through the stock during crosscuts, rather than the stock being pushed through a stationary blade (like on a table saw). During rip cutting and other functions, it works more like a table saw, with the stock being pushed through the saw blade that has been temporarily locked in place

Uses for a Radial-Arm Saw

Radial-arm saws are heavy, bulky machines that typically are not very portable. They are also fairly expensive and are somewhat difficult to keep in alignment. All these factors make them more common in dedicated wood shops, where portability isn’t a concern and the owners can master their use. While it is mainly a crosscut saw, this tool can be used to rip, cut bevels or miters, dadoes and rabbets, form moldings, and in some cases, even serve as a guide for a router. There are trade-offs to all of this versatility. For one, many radial-arm saws are more difficult to set up cuts than some other tools. For instance, to cut compound miters, it’s easier and quicker to set up a compound miter saw than a radial arm saw. To rip-cut stock, a table saw is a much faster setup. A radial-arm saw can handle both tasks with ease, which gives considerable value despite its hefty purchase price.

How to Use a Radial-Arm Saw

As with all tools, be sure to read and thoroughly understand the instructions that accompany your tool before you begin to use your radial-arm saw. Making sure that your saw is set up properly as per the manufacturer’s specs will not only teach you the features of the saw but how to use it safely. Each technique will require specific knowledge.

Crosscutting

When crosscutting with a radial arm saw, set the blade depth just below the surface of the table. If you’re using your saw for the first time, you’ll end up cutting some grooves into the sacrificial tabletop, so lower the blade to the cutting position after the saw’s motor is up to speed. Never free-hand any work on a radial-arm saw. Always hold the stock securely against the fence. as you pull the saw toward you, through the stock, the blade’s rotation is cutting away from the body. This will cause sawdust to blow away from the user, but it can also cause the saw blade to lurch or climb forward toward you as it cuts through the stock. With this in mind, keep the pressure on the handle and don’t let the saw determine the speed of the cut. The motion of pulling the saw toward your body and then holding it back while the blade is cutting can take some practice. Some users adapt to this peculiarity of the saw by starting crosscuts with the blade pulled forward and pushing the spinning blade back toward the fence to cut through the stock.

Dadoes and Rabbets

The radial-arm saw is the perfect tool for cross-cutting dadoes and rabbets, particularly when making tenons or slots for shelf standards. Raise the blade away from the table and install your stacked dado set to the thickness desired, making certain to install it in the proper direction for the rotation of the blade. Once the dado set is installed and the blade guard reattached, use a scrap piece of stock to help you determine the proper depth of cut for your dado. When the setup is complete, cutting dadoes and rabbets is as simple as making standard crosscuts. The same dado set also makes cutting tenons a breeze.

Miters and Bevels

A radial arm saw can typically cut miters of up to sixty degrees to either the left or right, and bevels of up to ninety degrees, but typically only in one direction. While this allows a radial-arm saw to cut more complex compound angles than a compound miter saw, it can also be a bit more challenging to get the angles just right. Always check to make sure the clamping levers on the saw are locked in place before beginning a cut.

Ripping

A less popular, but no less useful function of the radial-arm saw is to use it to rip stock. While there are some limitations of widths of cut that can be performed on a radial-arm saw, once the setup is completed, it is no less difficult to use than a table saw. When setting up your radial-arm saw to rip, be certain to always make use of the anti-kickback assembly, consisting of a riving knife and pawls. The riving knife is designed to help keep the stock from binding on the blade. If the blade jams during a rip cut, the pawls are designed to grab the stock and prevent it from kicking back. Make it a habit to always set the depth of the riving knife and pawls to the size of the stock, according to the instructions that come with your radial arm saw. When ripping melamine or other plastic-laminated stock, the pawls may not grip the stock in the event of kickback.